Standards

Fabric Inspection Procedure: SOP Template and Flow Chart

A fabric inspection procedure to adopt as your SOP: scope, roles, sampling, set-up, 4-point grading, records and a flow chart from receipt to cutting.

Quick answer: A fabric inspection procedure (SOP) defines who inspects which rolls, how, and what happens next: receive and record tickets, sample to the buyer's plan, set up light and speed, score defects by the 4-point system (ASTM D5430), check width, length, bow and skew (ASTM D3882), grade, hold and claim failures, relax and release to cutting, and keep the records.

By Radiatus team · Published 04 Nov 2026 · Updated 04 Nov 2026 · 10 min read

A fabric inspection procedure is the written method a mill or garment unit follows to inspect fabric rolls: which rolls are inspected, under what conditions, how defects are scored, how rolls are graded and what happens to a roll that fails. Written as a standard operating procedure (SOP), it makes inspection repeatable across inspectors and shifts, and it is what a buyer's auditor asks to see. This guide gives a copy-ready fabric inspection SOP template with a process flow chart, for any fabric. For knit-specific technique, see our guide to inspecting knitted fabric with the 4-point system; for a printable stage-by-stage list to tick off, see the fabric inspection checklist.

What is a fabric inspection procedure, and why write it as an SOP?

Every factory has a way of inspecting fabric. The difference between a way and a procedure is that a procedure is written down, names who is responsible, refers to the standards and buyer manuals it follows, and says which records prove it was followed. Writing it as an SOP has three practical benefits. New inspectors learn the same method as experienced ones. Results from two inspectors, two shifts or two units can be compared. And when a buyer disputes a roll, or the factory disputes a mill's claim, the SOP and its records show exactly how the roll was judged.

The SOP should be short enough to be read and specific enough to be followed. Where a value depends on the buyer (limits, tolerances, sampling plans, lighting), the SOP should say "as per the buyer manual" and point to where those values are kept, rather than copying numbers that will go out of date.

Fabric inspection process flow chart

The flow from receipt to cutting, with the two decision points that matter: pass or fail at grading, and relaxation complete or not before release.

1. Receive · record tickets 2. Sample to buyer's plan 3. Set up: light, speed, standard 4. Inspect · score defects 5. Width, length, bow, skew 6. Grade: pass? 7a. Hold · debit note 7b. Label · relax (timed) 8. Release to cutting · file Increase to 100 % if lot fails FAILPASSlot pass rate low

SOP template

Copy the sections below into your own document, replace the bracketed parts and remove anything that does not apply. Keep buyer-specific values in the buyer manual or your software's buyer standards, and refer to them from the SOP.

1. Purpose and scope

Purpose: to inspect incoming [or outgoing] fabric rolls consistently, grade them against each buyer's requirements, prevent failed fabric from reaching the cutting table, and keep evidence for buyers and for claims to supplying mills.

Scope: all woven and knitted fabric received at [factory / unit] for production, and [all finished fabric dispatched from the mill]. Excludes trims, interlinings and laboratory testing, which follow separate procedures.

2. References

  • ASTM D5430, Standard Test Methods for Visually Inspecting and Grading Fabrics (the 4-point system), or the 10-point or Graniteville system where the buyer manual specifies it.
  • ASTM D3882, bow and skew in woven and knitted fabrics.
  • ISO 2859-1, sampling procedures for inspection by attributes, where the buyer's sampling plan uses it.
  • The buyer's quality manual for each order: limits, hole rule, tolerances, lighting, sampling and report format.
  • Related SOPs: fabric relaxation, shade banding, shrinkage testing, claims to mills.

3. Responsibilities

ActivityStore in-chargeInspectorQC headMerchandiser
Receive rolls, record tickets and weightsR—II
Select the sample per the buyer's planCIA / RI
Set up frame, light and buyer standard—RA—
Inspect, score defects, measure checks—RA—
Grade rolls, decide hold or releaseICA / RI
Raise claims to the mill——CA / R
Relax and release to cuttingR—AI
Keep records, review this SOPC—A / RC

R = responsible, A = accountable, C = consulted, I = informed.

4. Procedure

  1. Receive. Check the packing list against the PO. Record each roll's number, lot or dye lot and ticket length or weight before any roll is opened. Weigh knit rolls and subtract the tube and polybag.
  2. Identify. Register each roll with PO, lot, shade, mill, buyer, width and GSM, and label it so it can be traced through inspection and cutting.
  3. Sample. Select the rolls to inspect according to the buyer's sampling plan (see the sampling table below), spread across colours, widths and constructions and across the delivery.
  4. Set up. Check the lighting at the frame against the buyer manual, set the frame speed to the factory's chosen setting for the fabric, and select the buyer standard for the order.
  5. Inspect. Run the roll face up through its full length. Log every visible defect with its type, yard position and size or points under the buyer's scoring system; photograph major defects and holes.
  6. Apply the rules. Cap points at 4 per linear yard (4-point system); score running defects for every yard they continue; apply the buyer's hole rule and running-defect reject length.
  7. Measure. Record width at start, middle and end, measured length against the ticket, bow and skew per ASTM D3882, and shade side-centre-side; cut a GSM sample.
  8. Grade. Calculate points per 100 sq yd (points × 3600 ÷ (yards × width in inches)) and compare with the buyer's roll limit and tolerances. Grade first quality, second quality or reject.
  9. Hold and claim. Tag failed or short rolls as on hold, keep them away from cutting, and pass the evidence to the merchandiser for a claim to the mill. Increase the sample to 100 % when the lot's results call for it under the buyer's plan.
  10. Release. Label passed rolls with their result, start relaxation where required, and release them to cutting only when relaxation is complete. Group rolls by shade band for the lay.

5. Records

  • Roll register with ticket and measured length or weight.
  • Inspection record per roll: defects with positions and points, roll map, photos, result and inspector.
  • Check records: width, length, bow, skew, shade, GSM, shrinkage where tested.
  • Lot summary report sent to the buyer; debit notes and mill responses.
  • Relaxation records and release to cutting.
  • Retention: [period agreed with buyers, for example at least as long as the buyer's claim period].

6. Frequency and review

Inspection runs on every lot received [and every lot dispatched]. The QC head reviews this SOP at least once a year, after any change in buyer requirements or equipment, and after any buyer complaint traced to fabric. Inspectors are re-trained on changes and, periodically, a sample of their rolls is re-inspected by the QC head to check consistency.

Sampling: how many rolls to inspect

The buyer's plan decides. These are the plans that appear most often in buyer manuals:

PlanHow many rollsWhen it is used
10 % conventionAt least 10 % of rolls per colour, width and construction, with a minimum number of rollsThe common default for incoming fabric
100 %Every rollWhen the previous lot from the mill failed, for critical orders, or for mills inspecting their own output
Square root√ (number of rolls), rounded upSome buyers' manuals
ISO 2859-1Sample size from the lot size and inspection level (often general level II), with acceptance numbersBuyers who specify AQL-style sampling for rolls

Whatever the plan, pick the sampled rolls from across the delivery, not the top of the stack, and write the plan and the selected rolls on the record.

Set-up: light, speed, buyer standard

Three things change what an inspector sees: the light, the speed and the standard. The SOP should require that the lighting at each frame meets the buyer manual and is checked at the start of each shift, that the frame speed is set to the factory's chosen setting for the fabric type and recorded (the right speed depends on the fabric, the defect types and the frame, so record your setting rather than copying someone else's number), and that the correct buyer standard is selected before the first roll. Most scoring disputes between factories and buyers trace back to one of these three.

Grading, hold and claims

A roll is judged against the buyer's limit for its scoring system, usually points per 100 square yards under the 4-point system, and against the tolerances for width, length, bow, skew, shade and GSM. Any one failure fails the roll unless the buyer manual says otherwise. Failed rolls are held, not cut, and the evidence goes into a claim to the mill; our guide on raising a debit note to a fabric mill covers that step. The differences between the 4-point, 10-point and Graniteville systems are explained on our scoring systems page.

After inspection: relaxation, shade bands, release

Passing inspection does not mean ready to cut. Knits and stretch fabrics need relaxation for the hours the buyer manual sets; rolls must be grouped by shade band so a garment never mixes bands; and only passed, relaxed rolls are released, with the cut number recorded. Our page on fabric relaxation: time chart, SOP and report format covers that part of the procedure.

Running this SOP on tablets

Fabric Inspection Software follows the same steps on an Android tablet. Rolls are registered with ticket figures and QR labels; the buyer standard carries the scoring system, limits, tolerances and sampling plan, so the sample is drawn for you; inspectors log defects by tap or voice with photos, offline when needed, and the app applies the per-yard cap and computes the result live; width, length, bow, skew, shade and GSM are recorded on the roll; failed rolls draft a debit note; relaxation is timed on a board that locks release to cutting; and every entry carries the inspector's name and time, with PIN switching on shared tablets. The QC head can re-inspect a sample of rolls as an audit and see how closely inspectors agree. See how the fabric inspection app works and the plans from ₹4,999 a month on the pricing page.

Questions people ask

What is the procedure for fabric inspection?

Receive the rolls and record ticket figures, sample them to the buyer's plan, set up light, speed and the buyer standard, inspect each sampled roll and score defects (usually by the 4-point system), measure width, length, bow and skew, grade against the buyer limit, hold and claim failures, then relax and release passed rolls to cutting.

What is the SOP for fabric inspection in the garment industry?

A written procedure with purpose and scope, references (ASTM D5430, ASTM D3882, ISO 2859-1 where used, buyer manuals), responsibilities, step-by-step procedure, records and review frequency. Garment exporters apply it to incoming fabric before cutting; the template in this guide follows that structure and can be copied and adapted.

What are the steps in the fabric inspection process flow chart?

Receive and record tickets, sample the lot, set up, inspect and score defects, measure checks, then grade. Failed rolls go to hold and a debit note; passed rolls are labelled, relaxed and released to cutting, and the records are filed. If the lot's results call for it, sampling increases to 100 %.

Which standard is used for fabric inspection?

Most buyers use the 4-point system described in ASTM D5430, which scores defects 1 to 4 points by length and normalises to 100 square yards. Some specify the 10-point system or Graniteville 78. Bow and skew are measured per ASTM D3882. The buyer manual always names the system and the limit.

What percentage of fabric rolls should be inspected?

As the buyer's sampling plan says. A common convention is at least 10 % of rolls per colour, width and construction, with 100 % inspection when the previous lot failed; some buyers use the square root of the roll count or ISO 2859-1 sample sizes. Mills inspecting their own output often inspect every roll.

How is a fabric roll graded after inspection?

By its points per 100 square yards against the buyer's roll limit, together with width, length, bow, skew, shade and GSM tolerances. Rolls within all limits are first quality; many mills grade rolls over the points limit as second quality, and rolls failing other checks may be rejected outright.

What records should fabric inspection keep?

The roll register with ticket and measured quantities, each roll's defects with positions, points, photos and result, the check measurements, the lot report sent to the buyer, claims to the mill, and relaxation and release records. Keep them at least as long as the buyer's claim period.

Related guides

Inspect the first roll the same day

We load your defect master, buyer limits and report layout, then train your inspectors on the floor in Tirupur, Surat or Ludhiana, or over a video call. 14-day pilot, no card. Plans start at ₹4,999 a month with unlimited rolls, and every result follows the ASTM D5430 4-point rules and your buyer's own limit.